搜索
Search
1

热门关键词: 汽机油   柴机油   齿轮油   波箱油   液压油

搜索
Search
您的位置:
Homepage
>
>
>
In the injection mold, what should be paid attention to in the design of the push rod?
There is currently no content to display
Please add data record on website background.

推荐产品

联系
这是描述信息

服务热线:

新闻中心

In the injection mold, what should be paid attention to in the design of the push rod?

  • Author:
  • Origin:
  • Time of issue:2022-04-15 09:57
  • Views:

(Summary description)In modern industry, injection molds are widely used and can be used in the production of aviation, aerospace, electronics, machinery, ships and automobiles. There are also many precautions in the production process of injection molds. Let's take a look Look, the precautions in the design of the push rod of the injection mold.

In the injection mold, what should be paid attention to in the design of the push rod?

(Summary description)In modern industry, injection molds are widely used and can be used in the production of aviation, aerospace, electronics, machinery, ships and automobiles. There are also many precautions in the production process of injection molds. Let's take a look Look, the precautions in the design of the push rod of the injection mold.

  • Categories:Corporate News
  • Author:
  • Origin:
  • Time of issue:2022-04-15 09:57
  • Views:0
Information

In modern industry, injection molds are widely used and can be used in the production of aviation, aerospace, electronics, machinery, ships and automobiles. There are also many precautions in the production process of injection molds. Let's take a look Look, the precautions in the design of the push rod of the injection mold.

1. In the injection mold, the distance between the side hole of the push rod and other holes (such as screw holes, pin holes, return spring holes, cooling water holes, etc.) should be greater than 2.5mm.

2. The unilateral gap between the push rod and the push rod fixing plate should be about 0.5mm.

3. The unilateral gap between the push rod and the template should be about 0.5mm.

4. In the design, the standard size should be used as the size of the push rod, and the push rod head should not sink into the push rod fixing plate.

5. The guide holes of the push rod and the insert need to be matched according to H7/F7. However, in the injection molding of PA, LDPE and PP, the gap between the push rod and the push rod matching hole is less than 0.02mm. If it is too large, there will be flashes.

6. After the push rod is installed, the push rod fixing plate should be able to slide down automatically, and there should be no jamming phenomenon.

7. The fixed positions of the push rod and the push rod should be in one-to-one correspondence and marked to avoid installation errors.

8. When the forming part of the push rod is inclined or curved, it should be prevented from rotating to avoid wrong installation.

9. When designing the push rod position of the injection mold, it is not only required that the demoulding force is appropriate, but also ensure that the plastic parts are demolded in parallel.

10. If the height or demoulding slope of the plastic part is large, you need to draw a smaller contour line in the plan view, so that there will be no error when setting; Draw smaller contour lines. In order to ensure that the setting of the push rod is correct, if the top corner of the plastic part has a large rounded corner, it is necessary to draw a small contour line in the plan view. When the rounded corner is large, it should be drawn in the plan view. The tangent of the rounded corner is used as the boundary line of the putter position.

11. The distance between the push rod and the plastic part should be accurate, neither too far nor too close.

12. It is recommended to place the push rod at the bottom of the plastic part, not the top.

13. The plastic part needs to add a push rod on the inclined plane, because the push rod and the plastic part are easy to slide on the inclined plane, and the push force will be distributed accordingly, which greatly reduces the thrust force. The end face of the putter requires more than three small steps to increase thrust. At the same time, the putter head should also be prevented from turning.

14. For deeper columns (the height of the column is greater than 8mm), a push rod should be added at the bottom of the column as much as possible. In this way, not only the injection effect is good, but also the exhaust volume can be increased, which is beneficial to the melt filling. For short posts, add two push rods beside the post. Whether it is necessary to add an exhaust rod at the bottom of the column depends on the specific situation.

Scan the QR code to read on your phone

Online customer service
Customer service hotline
0769-85601899 0769-85601899
Service time:
8:30 - 18:00
Customer service group:
在线客服

Address: Dongguan Shanling Industrial Park Company | National Service Hotline:0769-8560 1899
Tel:
0769-8560 1899 | Fax:0769-85628228
E-mail:
cydg@chinyuan.com | Web:www.chinyuan.com

COPYRIGHT © 2022 CHIN YUAN EL ECTRONICS (DONG GUAN) CO, LTD. ALL RIGHTS RESERVED | Powered by:www.300.cn | 粤ICP备06124372号-1  SEO

1